Whetstone grit chart
The grit number tells you how coarse a stone is: low numbers cut fast and leave a rough edge, high numbers cut slowly and leave a fine one. A sharpening session goes from coarse to fine, starting only as coarse as the edge needs.
The chart
| Grit | Band | What the maker says it's for | Stone |
|---|---|---|---|
| 70 / 120 | Coarse | Extra coarse / coarse; start here for a very dull edge or a new angle | Lansky Deluxe |
| 280 | Coarse | Lansky calls it "Medium"; start here for touch-ups on that system | Lansky Deluxe |
| 320 | Coarse | "Coarse" diamond on the RKS discs; diamond face of the Precision Adjust rod | Work Sharp |
| 325 (45 microns) | Coarse | "restore a dull or damaged edge" | Sharpal 156N |
| 400 | Coarse | "smooth off any unevenness" | Wüsthof J 400/2000 |
| 600 | Medium | Fine (Lansky); fine diamond (Work Sharp) | Lansky, Work Sharp |
| 1000 | Medium | "restoring a dulled edge" (Shun); ultra fine on Lansky's system | Shun 1000/6000 |
| 1200 (12 microns) | Medium | "to hone" | Sharpal 156N |
| 2000 | Fine | finer side "used to hone and sharpen" | Wüsthof J 400/2000 |
| 6000 | Fine | "refresh and polish the edge" | Shun 1000/6000 |
The bands (coarse up to 400, fine from 2000) are our grouping, not a standard. Makers grade differently: Lansky calls 280 "medium" and 1000 "ultra fine," while Shun treats 1000 as the stone for a dulled edge. Read each stone's number with its maker's description.
How to use the chart
- Chipped or uneven edge: start coarse (325–400, or 70–120 on a Lansky). Work until a burr forms along the full edge, then go up through the bands.
- Dull, no damage: start medium (around 1000), finish fine.
- Lost its bite: a fine grit alone may be enough. Hone first, though; see honing vs sharpening.
- Polish: after medium, finish at 6000.
The grit selector does this with your own stones and tells you which bands your set is missing. The burr check that decides when to move up is described in how to tell if a knife is sharp.
How long to stay on each grit
There's no fixed count. Stay on a grit until it has done its job along the whole edge, then move up. On the coarse and medium stones, the sign is a burr you can feel along the full length. On the fine stones, it's a smooth, even scratch pattern and a clean paper cut. Moving up too early leaves deep scratches the finer stone can't remove. Staying on a coarse grit too long removes metal you didn't need to lose. The 15XV manual's warning about electric stages applies to stones too: "Do not over sharpen." Most routine sessions never touch the coarse band. Makers' schedules are in how often to sharpen.
Water, oil or dry
Stones differ here too. Shun says to soak its stone before use. Wüsthof says to submerge its stones for about ten minutes, until no more air bubbles rise. Sharpal's diamond plate is used dry: "No messy oil needed." Lansky's alumina oxide hones don't need oil, but Lansky suggests a few drops to lift metal filings when the stone starts to clog. HORL's diamond disc is also used dry.
Diamond or water stone?
Diamond plates (Sharpal 156N) stay flat and don't need soaking. Water stones (Shun, Wüsthof) are what most Japanese-style sharpening guides start with. Both are on whetstones for beginners. For a fixed-angle alternative, see whetstone vs electric.
FAQ
- Is 1000 grit enough?
- For regular sharpening, often yes. Shun calls its 1000 side the one for restoring a dulled edge. A finer stone (Shun pairs it with 6000) refines and polishes. Chips need a coarser grit.
- 1000 vs 6000 grit: what's the difference?
- Shun's combination stone uses 1000 to restore a dulled edge and 6000 to refresh and polish it. The 6000 side doesn't repair a dull edge on its own.
Specs verified: November 2026 · Updated 2026-11-18 · How we choose