What angle to sharpen kitchen knives
The best angle for your knife is the one its maker ground at the factory. Sharpen at that angle and the edge keeps its intended shape. Sharpen at a different angle and you slowly turn it into a different edge. Here are the published figures, in the makers' own words.
Per side or included?
Most knife makers quote the angle per side: the angle between one bevel and the center line of the blade. The included angle is the full V, twice the per-side angle on a symmetrical edge. HORL explains it this way: "the cutting angle is usually twice the grinding angle." Spyderco marks its Sharpmaker the same way: 30° is 15° each side and 40° is 20° each side. Sharpener makers usually quote per side too, but not always, so check before comparing numbers.
Factory angles by brand
| Brand and series | Angle | Basis | In the maker's words |
|---|---|---|---|
| WÜSTHOF — Classic, Ikon and other Western-style blades | 14° | per side | “standard blades is 14˚ per side” WÜSTHOF |
| WÜSTHOF — Asian-style (santoku, nakiri) | 10° | per side | “Asian-style (Santokus, Nakiris) 10˚ per side” WÜSTHOF |
| ZWILLING — ZWILLING knives (Western) | 15° | per side | “approximately 15° for ZWILLING knives” ZWILLING |
| ZWILLING — ZWILLING santoku | 9–12° | per side | “Santoku knives and all MIYABI knives should be 9-12°” ZWILLING |
| MIYABI — All MIYABI series | 9.5–12° | per side | “traditional, Japanese 9.5° to 12° edge angle; honed by hand at 9.5° to 12° (both sides)” MIYABI |
| Shun — Shun double-bevel knives | 16° | per side | “sharpened to a 16° angle on each side” Shun |
| Global — Global knives | 10–15° | not stated | “factory sharpened at an angle of between 10-15 degrees” Global |
| Victorinox — Kitchen knives (sharpening steel) | 30–40° | total (included) | “When using a sharpening steel, the angle should be between 30-40°” Victorinox |
| MAC — MAC knives | 15° | per side | “angle around 30 degrees (15 degrees per side)” MAC |
| Misen — Misen knives | 15° | not stated | “15-degree edge angle, symmetrical grind” Misen |
| Mercer Culinary — Genesis | 15° | not stated | “Blade Angle 15°” Mercer Culinary |
| Made In — 8-inch chef knife (asymmetric) | 14° | asymmetric | “14° front + 4° reverse (18° total)” Made In |
| Made In — Santoku | 12.5° | per side | “12.5-Degrees (Either Side)” Made In |
| Cutco — Double-D serrated edge | not published | — | “DO NOT use the Cutco Sharpener or any other sharpening service. It will ruin the special edge. Send them back to the Cutco factory.” Cutco |
| Cutco — Straight edge | not published | — | “no angle published; straight edges may be sharpened with a stone or steel” Cutco |
Victorinox's 30–40° is for the sharpening steel. Its regrinding sheet lists edge angles as included figures, so we read it as total, about 15–20° per side. Global, Misen and Mercer don't say per side or total.
Reading the table
Three groups stand out. German makers sit at 14–15° per side: Wüsthof's standard blades at 14° (its PEtec factory edge at 14.5°) and Zwilling at approximately 15°. Japanese-style edges go lower: Miyabi at 9.5–12°, Wüsthof's Asian-style santoku and nakiri at 10°, Zwilling's santoku at 9–12°, Made In's santoku at 12.5°. Shun is the exception among Japanese brands at 16° per side. Several brands that sell to both markets land around 15°: MAC ("around 30 degrees, 15 degrees per side"), Misen and Mercer's Genesis line.
Some edges don't fit a single number. Made In's chef's knife is asymmetric, 14° on the front plus 4° on the reverse, for 18° total. Cutco publishes no angle for straight edges and says its Double-D serrated edges must go back to the factory.
Edge shapes
A symmetrical double bevel is what most Western and many Japanese kitchen knives have, and what fixed-angle sharpeners are built for. A single-bevel knife, like a yanagiba, is flat on the back. Chef'sChoice's 15XV and 1520 manuals give a separate single-bevel procedure, sharpening the beveled side only. Tumbler says to check the knife maker's instructions first, and not to assume its 15° or 20° settings suit every single-bevel knife.
Matching a sharpener
- Fixed-angle sharpeners (most electrics and pull-throughs) grind at their built-in angle. A 20° machine will re-angle a 14° Wüsthof over a few sharpenings. The German knives page lists sharpeners at 14–15°.
- Adjustable systems like the Work Sharp Precision Adjust (15–30° in 1° steps) can be set to the maker's figure, as long as it's in range. See guided systems.
- Whetstones work at any angle, because you hold it, including Miyabi's 9.5–12°, which no fixed sharpener in our list reaches. See sharpeners for Japanese knives.
The angle finder does this matching for you. It also shows how close a fixed angle comes (within 2° per side by default, which you can change). For rolling sharpeners, the choice between their 15° and 20° blocks follows the same rule; see rolling sharpeners and HORL vs Tumbler.
Checking the angle you're actually sharpening
HORL suggests the marker method: run a felt-tip marker along the edge on both sides, then sharpen. When the ink is gone from both sides, you've reached the angle. More edge checks are in how to tell if a knife is sharp.
FAQ
- Is 15 or 20 degrees better for kitchen knives?
- Neither is better in general. Use the angle your knife maker publishes: Wüsthof says 14° per side, Zwilling about 15°, Shun 16°, Miyabi 9.5–12°.
- What's the difference between per side and included angle?
- Per side is the angle of one bevel. On a symmetrical edge the included angle is twice that, so 15° per side is a 30° edge.
Specs verified: November 2026 · Updated 2026-11-18 · How we choose