Do knife sharpeners ruin knives?

A sharpener doesn't ruin a knife on its own. Using it the wrong way does: on a knife it wasn't made for, at the wrong angle, or more often than needed. Every mistake below is one a knife or sharpener maker warns about in its own words.

Mistakes and who warns about them

MistakeWhat the maker saysSource
Electric sharpener on Global knives"We do not recommend using electric sharpeners. They tend to strip a lot of metal off the blade"Global (UK)
Sharpening a Cutco Double-D edge"DO NOT use the Cutco Sharpener or any other sharpening service. It will ruin the special edge."Cutco
15° knife in a 20° slot"Do not sharpen 15° knives in Stage 2"Chef'sChoice 4643 manual
Ceramic knives in a steel-knife machineNot for ceramic knives or scissorsChef'sChoice 15XV manual
Non-Kyocera ceramic in Kyocera's sharpener"cannot be sharpened properly"; no warranty when used on themKyocera
Serrated knife on a rolling diamond disc"The serrated heads of the bread knives are ground off and the surface of the diamond sharpening disc wheel can be damaged"Tumbler
Diamond steel for everyday honingShun advises against a diamond steel for regular honing of its knivesShun
Oil or water in a Chef'sChoice electric"do not use honing oils, water or any other lubricant"Chef'sChoice 1520 manual

1. The wrong angle

Every fixed-angle sharpener grinds the edge to its own angle. Put a 14° Wüsthof through a 20° machine and, over a few sessions, you get a 20° knife. That's not broken, but it's no longer the edge Wüsthof made, and you remove extra metal getting there. The same happens in reverse: Chef'sChoice's 15XV converts 20° edges to 15° on purpose. Check your knife's factory figure in the angle finder or the angle guide.

2. Sharpening when honing would do

Shun says sharpening "should be done only when the knife truly needs it," because it removes metal. Honing doesn't. Many "dull" knives only need their edge realigned. The hone-or-sharpen tool helps you tell the difference.

3. Too many passes

Manuals give pass counts for a reason. The 15XV manual describes making pulls until a small burr forms along the full edge, then moving on. It also warns: "Do not over sharpen." Each extra pass on a coarse stage takes metal you didn't need to lose. The Chef'sChoice 4643 manual warns against making many strokes in stage 2 on serrated blades, because it can quickly remove metal from a serrated edge.

4. The wrong knife in the wrong tool

Ceramic knives, serrated knives and single-bevel knives each need a tool whose maker allows them. Chef'sChoice manuals rule out ceramic. Tumbler rules out serrated and ceramic. Kyocera only covers Kyocera ceramic knives. Single-bevel knives get their own procedure in the Chef'sChoice 15XV and 1520 manuals, and Chef'sChoice sends them away from the 4643. The serrated page lists who allows what.

5. Fixing damage the hard way

A chip means removing metal back to below the chip. Shun's service does this for chips of 2 mm or under, and notes that the blade ends up narrower and the edge a little thicker. Bigger chips, cracks or broken tips are better left to the maker or a professional than ground out on a pull-through.

6. Ignoring the warranty and service options

Several knife makers would rather sharpen their knives themselves. Shun sharpens Kai knives free for as long as you own them, and you pay shipping and processing. Cutco requires its Double-D edges to go back to the factory. Kyocera, for its part, says its DS-38 won't sharpen other brands' ceramic knives properly and that no warranty applies when it's used on them. Before you sharpen a knife at home, read what its maker says, which is usually one page on its site.

The short version

  1. Match your knife's factory angle.
  2. Hone first; sharpen only when honing stops working.
  3. Follow the manual's slot and pass counts.
  4. Check that the maker lists your knife type: serrated, ceramic, single-bevel.
  5. Send real damage to the maker.

Electric options that follow these rules are on electric sharpeners, and the trade-offs by type are on electric vs manual vs whetstone.

FAQ

Do electric knife sharpeners ruin knives?
Global (UK) says it doesn't recommend electric sharpeners because they tend to strip a lot of metal off the blade. Other knife makers don't rule them out; Shun accepts one equivalent to its own. Matching the angle and following the manual is what matters.
Are pull-through sharpeners bad?
They grind at a fixed angle. Used at the knife's angle and as the manual says, they do what they're designed to do. Used on the wrong knife or in the wrong slot, they change the edge.